Brugsanvisning Makita DSP601 Rundsav

Brugsanvisning

10 ENGLISH

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool.Failuretofollowallinstructions

listedbelowmayresultinelectricshock,reand/or

seriousinjury.

Save all warnings and instruc-

tions for future reference.

Theterm"powertool"inthewarningsreferstoyour

mains-operated(corded)powertoolorbattery-operated

(cordless)powertool.

Cordless circular saw safety

warnings

Cutting procedures

1.

DANGER: Keep hands away from cutting

area and the blade. Keep your second hand

on auxiliary handle, or motor housing.Ifboth

hands are holding the saw, they cannot be cut by

the blade.

2. Do not reach underneath the workpiece.The

guardcannotprotectyoufromthebladebelowthe

workpiece.

3. Adjust the cutting depth to the thickness of

the workpiece.Lessthanafulltoothoftheblade

teeth should be visible below the workpiece.

4. Never hold the workpiece in your hands or

across your leg while cutting. Secure the

workpiece to a stable platform. It is important to

support the work properly to minimise body expo-

sure,bladebinding,orlossofcontrol.

►Fig.1

5. Hold the power tool by insulated gripping

surfaces, when performing an operation where

the cutting tool may contact hidden wiring or

its own cord.Contactwitha"live"wirewillalso

makeexposedmetalpartsofthepowertool"live"

and could give the operator an electric shock.

6. When ripping, always use a rip fence or

straight edge guide.Thisimprovestheaccuracy

ofcutandreducesthechanceofbladebinding.

7. Always use blades with correct size and shape

(diamond versus round) of arbour holes.

Blades that do not match the mounting hardware

ofthesawwillrunoff-centre,causinglossof

control.

8. Never use damaged or incorrect blade wash-

ers or bolt.Thebladewashersandboltwere

speciallydesignedforyoursaw,foroptimum

performanceandsafetyofoperation.

Kickback causes and related warnings

— kickback is a sudden reaction to a pinched,

jammedormisalignedsawblade,causingan

uncontrolledsawtoliftupandoutoftheworkpiece

toward the operator;

— whenthebladeispinchedorjammedtightlybythe

kerfclosingdown,thebladestallsandthemotor

reaction drives the unit rapidly back toward the

operator;

— ifthebladebecomestwistedormisalignedinthe

cut,theteethatthebackedgeofthebladecandig

intothetopsurfaceofthewoodcausingtheblade

toclimboutofthekerfandjumpbacktowardthe

operator.

Kickbackistheresultofsawmisuseand/orincorrect

operating procedures or conditions and can be avoided

by taking proper precautions as given below.

1. Maintain a rm grip with both hands on the

saw and position your arms to resist kickback

forces. Position your body to either side of the

blade, but not in line with the blade.Kickback

couldcausethesawtojumpbackwards,but

kickbackforcescanbecontrolledbytheoperator,

ifproperprecautionsaretaken.

2. When blade is binding, or when interrupting a

cut for any reason, release the trigger and hold

the saw motionless in the material until the

blade comes to a complete stop. Never attempt

to remove the saw from the work or pull the

saw backward while the blade is in motion

or kickback may occur. Investigate and take

correctiveactionstoeliminatethecauseofblade

binding.

3. When restarting a saw in the workpiece, centre

the saw blade in the kerf so that the saw teeth

are not engaged into the material.Ifasawblade

binds,itmaywalkuporkickbackfromthework-

piece as the saw is restarted.

4. Support large panels to minimise the risk of

blade pinching and kickback. Large panels tend

to sag under their own weight. Supports must be

placed under the panel on both sides, near the line

ofcutandneartheedgeofthepanel.

►Fig.2

►Fig.3

5. Do not use dull or damaged blades.

Unsharpened or improperly set blades produce

narrowkerfcausingexcessivefriction,blade

binding and kickback.

6. Blade depth and bevel adjusting locking levers

must be tight and secure before making the

cut.Ifbladeadjustmentshiftswhilecutting,itmay

cause binding and kickback.

7. Use extra caution when sawing into existing

walls or other blind areas.Theprotrudingblade

maycutobjectsthatcancausekickback.

8. ALWAYS hold the tool rmly with both hands.

NEVER place your hand, leg or any part of your

body under the tool base or behind the saw,

especially when making cross-cuts.Ifkickback

occurs,thesawcouldeasilyjumpbackwardsover

yourhand,leadingtoseriouspersonalinjury.

►Fig.4

9. Never force the saw. Push the saw forward at a

speed so that the blade cuts without slowing.

Forcingthesawcancauseunevencuts,lossof

accuracy, and possible kickback.

Bedømmelse

Mere om denne brugsanvisning

Vi forstår, at det er rart at have en papirbrugsanvisning til din Makita DSP601 Rundsav. Du kan altid downloade brugsanvisningen fra vores hjemmeside og selv printe den. Hvis du gerne vil have en original brugsanvisning, anbefaler vi, at du kontakter Makita. De kan muligvis levere en original brugsanvisning. Leder du efter brugsanvisningen til din Makita DSP601 Rundsav på et andet sprog? Vælg dit foretrukne sprog på vores hjemmeside, og søg efter modelnummeret for at se, om vi har det tilgængeligt.

Specifikationer

Alle brugsanvisninger til Makita Rundsave
Flere brugsanvisninger til Rundsave

Ofte stillede spørgsmål om Makita DSP601 Rundsav

Vores support-team søger efter nyttige produktoplysninger og svar på ofte stillede spørgsmål. Hvis du finder urigtigheder i vores ofte stillede spørgsmål, må du meget gerne lade os det vide ved at bruge vores kontaktformular.

Relaterede produkter

Brugsanvisning

Makita LS1016L Rundsav

Brugsanvisning

Makita BCS550ZX Rundsav

Brugsanvisning

Makita CC301D Rundsav

Brugsanvisning

Makita 4105KB Rundsav

Brugsanvisning

Makita 4114S Rundsav

Brugsanvisning

Makita EK7650H Rundsav

Brugsanvisning

Makita BSS500RFX Rundsav

Brugsanvisning

Makita DSS610 Rundsav

Relaterede kategorier