Brugsanvisning JBL Control X Højttaler

Brugsanvisning

3

www.jbl.com

ENGLISH

WALL-MOUNTING THE SPEAKERS USING

INCLUDED WALL BRACKETS

Adjustable wall brackets are included for the JBL Control X speakers.

The included brackets are for wall-mounting only.

Ceiling-mounting these JBL Control X speakers is not recommended,

regardless of the bracket used.

IMPORTANT SAFETY NOTE: Proper selection of mounting

hardware not included herein, and proper assembly and

installation of brackets, in cluding, but not limited to, selection

of appropriate weight-bearing support and bracket use with

the specified speaker only is the exclusive responsibility of the

customer. Manufacturer disclaims any liability for the selection of

mounting hardware and/or bracket installation.

A. Loosen and remove the molded nut (2) by turning it counterclockwise.

Use the supplied metal bar (5) if necessary by inserting it in one of the

holes on the molded nut (2).

B. Pull the ball/shaft (3) out of the wall bracket (4).

C. Slide the molded nut (2) onto the ball/shaft (3) with threaded opening

facing the ball, and thread on the metal nut (1) all the way onto the

ball/shaft (3), with the nut’s (1) “knurled” surface facing away

from the ball.

D. Screw the ball/shaft (3) into the threaded 3/8"-16 insert (6) on the

back of the speaker cabinet until it is fully seated against the bottom

of the insert. Back out the ball-shaft assembly one half turn and

tighten the nut against the speaker. If the ball and shaft assembly

is not backed out before tightening the nut, performing Step G

below may dislodge the threaded insert in the speaker housing and

permanently damage the speaker.

E. Tighten the “knurled” nut (1) using a crescent wrench until it is firmly

seated against the back of the speaker and has fully locked the ball/

shaft (3) and the speaker cabinet together. Please note that once

this nut is tightened, it may embed some marks on the back of the

speaker where the attachment is made. However, these marks will be

covered by the nut (1).

F. The security cable (8) is provided as an additional measure to prevent

the speaker from falling in case the speaker becomes detached from

the wall bracket. One of the two lower screws (9) that attach the wall

bracket (4) to the wall will need to go through the eyelet (11) at the

end of the cord before going through the wall-bracket hole. Make sure

that the screw head is at least 0.36" (approximately 3/8") or larger in

diameter so that it can properly hold the backup cord eyelet (11).

G. Mount the wall bracket (4) onto a wood stud on the wall, using #10,

minimum 1", panhead wood screws. Make sure that all four screws

are driven into the stud, not drywall.

If the bracket needs to be mounted on drywall, the use of properly

selected and installed wall anchors and screws is essential.

H. Securely attach the other end (10) of the security cable (8) to the

Control X by engaging it through the bar (12) on the back speaker,

as shown in the illustration.

I. Connect your speaker wire to the terminals (13) on the rear of

the speaker. Be sure to leave enough cable if mounting speakers in

horizontal position.

J. Holding the speaker cabinet (7) with both hands, reinsert the ball

portion of the ball/shaft (3) into the wall bracket (4).

K. Hand-tighten the molded nut (2) while positioning the speaker for the

intended orientation.

L. Once the orientation of the speaker is finalized, use the metal bar (5) in

one of the holes on the molded nut (2) and tighten securely.

DO NOT OVERTIGHTEN THE MOLDED NUT (2).

HORIZONTAL ORIENTATION

LEFT SPEAKER RIGHT SPEAKER

Note: Be sure to rotate the JBL grille badge 90 degrees if you are

mounting these speakers in the horizontal position. Simply

remove the grille, push the badge from the inside and rotate

it accordingly.

INCORRECT

CORRECT

Bedømmelse

Mere om denne brugsanvisning

Vi forstår, at det er rart at have en papirbrugsanvisning til din JBL Control X Højttaler. Du kan altid downloade brugsanvisningen fra vores hjemmeside og selv printe den. Hvis du gerne vil have en original brugsanvisning, anbefaler vi, at du kontakter JBL. De kan muligvis levere en original brugsanvisning. Leder du efter brugsanvisningen til din JBL Control X Højttaler på et andet sprog? Vælg dit foretrukne sprog på vores hjemmeside, og søg efter modelnummeret for at se, om vi har det tilgængeligt.

Specifikationer

Alle brugsanvisninger til JBL Højttalere
Flere brugsanvisninger til Højttalere

Ofte stillede spørgsmål om JBL Control X Højttaler

Vores support-team søger efter nyttige produktoplysninger og svar på ofte stillede spørgsmål. Hvis du finder urigtigheder i vores ofte stillede spørgsmål, må du meget gerne lade os det vide ved at bruge vores kontaktformular.

Relaterede produkter

Brugsanvisning

JBL Duet Højttaler

Brugsanvisning

JBL Pulse 3 Højttaler

Brugsanvisning

JBL Bar 2.0 All-in-One Højttaler

Brugsanvisning

JBL Flip Højttaler

Brugsanvisning

JBL Jembe Højttaler

Brugsanvisning

JBL Go 3 Højttaler

Brugsanvisning

JBL Go Højttaler

Brugsanvisning

JBL Pulse 2 Højttaler

Relaterede kategorier