Brugsanvisning Hoover HVI 640 X Kogesektion

Brugsanvisning

Installing a domestic appliance can be a complicated operation which if not carried out correctly, can seriously affect consumer

safety. It is for this reason that the task should be undertaken by a professionally qualified person who will carry it out in

accordance with the technical regulations in force. In the event that this advice is ignored and the installation is carried out

by an unqualified person, the manufacturer declines all responsibility for any technical failure of the product whether or not

it results in damage to goods or injury to individuals.

2 GB

BUILT-IN

The furniture in which your hob will be installed and all adjacent

furniture, should be made from materials that can withstand high

temperatures. In addition, all decorative laminates should be fixed

with heat-resistant glue.

Installation:

• A watertight seal is supplied with the hob.

Before fitting:

- turn the hob upside down, with the glass surface facing downwards.

Make sure the glass is protected.

- fit the seal round the hob.

- make sure that it is correctly fitted to avoid any leakage into the

supporting cabinet.

• It it important to fit the hob on a level supporting surface.

• Deformations caused by incorrect fitting can alter the specifications

of the worktop and the performance of the hob.

• Leave a gap of at least 5 cm between the appliance and any

neighbouring vertical surfaces.

• It is absolutely essential that the recess conforms with the

dimensions indicated.

• The height of the flush-mounted part of the hob is 5,5 cm.

• If there is an intermediate division :

- the clearance between the bottom of the casing and an

intermediate floor or part of a furniture unit must greater than

2,5 cm so as to allow air circulate.

The minimum distance should be 8 cm.

- furthermore, you should ensure that there is at the rear a

ventilation (8 cm) on all the width.

• You can not build the hob in above an oven with no fan, a

dishwasher, fridge, freezer or washing machine.

• The body of the hob is fitted which 4 location holes to take the

fixing clamps intended to fix the hob in the unit. Place the 4 fixing

clamps, before building-in the hob, in such a way that the hob

is placed perfectly in the support unit.

INSTALLATION

Seal

Hob

25 mm

mini

50 mm

Opening

500 X 50

Opening

500 X 10

"The installation must conform to the standard directives."

The manufacturer declines all responsibility for any damage that

may be caused by unsuitable or unreasonable use.

Warning :

• Always check before any electrical operation, the supply tension

shown on the electricity meter, the adjustment of the circuit-

breaker, the continuity of the connection to earth to the installation

and that the fuse is suitable.

• The electrical connection to the installation should be made via

a socket with a plug with earth, or via an omnipole cut-out switch

with an opening gap of at least 3 mm.

If the appliance has a socket outlet, it must be installed so that

the socket outlet is accessible.

ELECTRICAL CONNECTION

• The yellow/green wire of the power supply cable must be

connected to the earth of both power supply and appliance

terminals.

• The manufacturer cannot be held responsible for any accidents

resulting from the use of an appliance which is not connected

to earth, or with a faulty earth connection continuity.

• Any queries regarding the power supply cord should be referred

to After Sales Service or a qualified technician.

The hob is fitted with a power supply cord which allows it to

be connected only to a power supply of 220-240 V between

phases or between phase and neutral.

• Connect to a socket, to choose the correct fuse, you must refer

on the table.

It is however possible to connect the hob to :

Two phases 220-240V2~, Threephases 220-240V3~

or Three phases 380-415V3N~.

To proceed to the new connection, you must adhere the following

instructions.

• Before making the connection make sure that the installation is

protected by a suitable fuse, see table, and that it is fitted with

wires of a large enough section to supply the appliance normally.

1- Operations to be carried out on the existing connection :

- turn over the hob, glass side against the work top, taking care

to protect the glass.

- open the cover.

- pull out the supply cord :

. remove the screws retaining the shunt bars and the conductors

of the supply cord,

. unscrew he cable clamp to release the power supplying cord,

. pull out the supply cord.

2- Operations to be carried out to make a new connection :

- choose the power supply cord in accordance with the

recommendations in the table.

- pass the power supply cable into the clamp.

- strip the end of each conductor of the supply cord on a 10 mm

length, by taking in account the requested length of the cord for

the connection to the terminal block.

- according to the installation and with the help of shunt bars which

you should have recovered in the first operation, fix the conductor

as shown on the chart.

- screw the cable clamp and fix the cover.

CONNECTION TO THE TERMINALS ON THE TERMINAL BLOCK:

HVI 740

HVI 640

Bedømmelse

Mere om denne brugsanvisning

Vi forstår, at det er rart at have en papirbrugsanvisning til din Hoover HVI 640 X Kogesektion. Du kan altid downloade brugsanvisningen fra vores hjemmeside og selv printe den. Hvis du gerne vil have en original brugsanvisning, anbefaler vi, at du kontakter Hoover. De kan muligvis levere en original brugsanvisning. Leder du efter brugsanvisningen til din Hoover HVI 640 X Kogesektion på et andet sprog? Vælg dit foretrukne sprog på vores hjemmeside, og søg efter modelnummeret for at se, om vi har det tilgængeligt.

Specifikationer

Alle brugsanvisninger til Hoover Kogesektioner
Flere brugsanvisninger til Kogesektioner

Ofte stillede spørgsmål om Hoover HVI 640 X Kogesektion

Vores support-team søger efter nyttige produktoplysninger og svar på ofte stillede spørgsmål. Hvis du finder urigtigheder i vores ofte stillede spørgsmål, må du meget gerne lade os det vide ved at bruge vores kontaktformular.

Relaterede produkter

Brugsanvisning

Hoover HVH 551/1 X Kogesektion

Brugsanvisning

Hoover HPI44PW Kogesektion

Brugsanvisning

Hoover HVH 750/1 X Kogesektion

Brugsanvisning

Hoover HI624TCT/1 Kogesektion

Brugsanvisning

Hoover HI642C Kogesektion

Brugsanvisning

Hoover HVH 750/2 X Kogesektion

Brugsanvisning

Hoover HVH551X Kogesektion

Brugsanvisning

Hoover HTP634DB3 Kogesektion

Relaterede kategorier