Brugsanvisning FERM TCM1001 Fliseskæremaskine

Brugsanvisning

Caution! For your own safety, carefully read these

instructions for use before using the machine.

TECHNICAL SPECIFICATIONS

6 mm

400 mm

30 -80 mm

0-45

o

TABLE OF CONTENTS:

1. SPECIAL SAFETY INSTRUCTIONS

2. ASSEMBLY

3. HOW TO CUT AND BREAK TILES

4. MAINTENANCE

Faulty and/or discarded electrical or electronic

apparatus have to be collected at the appropriate

recycling locations.

1. SPECIAL SAFETY

INSTRUCTIONS

1. The tile cutting machine is fitted with a replaceable

circular blade. Therefore, keep children away.

2. After use the machine must be stored in a safe and

dry place, away from children.

3. This machine has been designed for cutting and

breaking glazed tiles, and must not be used for any

other purpose.

4. When using the tile cutting machine make sure to

keep extension leads and such away from the

machine.

5. Always place the tile cutting machine on a level and

firm surface.

6. CAUTION! The edges of cut tiles are sharp.

2. ASSEMBLY

Assemble the tile cutting machine as shown in the

drawing.

ASSEMBLY OF THE TILE CUTTING

MACHINE

Remove all the parts from the box and assemble the tile

cutting machine as follows:

1. Slide the black rubber feet (T) over the corners of

the tile cutter. Slide a washer onto the bolt and push

this into the rubber foot. Now slide a washer and a

nut over the bolt on the back and fasten this

properly. Repeat this for the other three corners.

2. Mount the fastening blocks (N) with the 2 tubes (M)

onto the bottom plate (V) using the 4 bolts (O) and

washers (P).

3. Screw the lever (H) onto the tube fastening (I).

4. Finally, mount the sash angle (U) onto the bottom

plate (V) using the knob (S) and washer.

ASSEMBLY OF THE HOLLOW SQUARE

CHISEL

1. Place the hollow square chisel above the hole in the

bottom plate (V).

2. Make sure that the clamping plate (E) comes under

the 2 tubes and fasten this using the socket head

wrench supplied. The socket head wrench is situated

in the black fastening plate (C).

3. It is important that the drill (G) and the knife (F) are

adjusted in such a way that they just touch the

bottom plate (V). This adjustment can be done using

the two nuts at the top of the hollow square chisel.

Then fasten these nuts against each other.

3. HOW TO CUT AND BREAK TILES

1. Use a soft-tipped (carpenter’s) pencil to mark off the

cutting line.

2. Place the tile against the stop, the glazed side facing

upward. The pencil mark must be directly below the

blade.

3. Firmly hold the tile and cut several times (at least 4)

along the mark. After each cut, press the lever more

firmly.

4. Lift the lever when it has reached the front edge of

the tile and moved it backward.

5. Subsequently the break-off unit is lifted. Repeat along

the full width of the tile until the notch is sufficiently

deep.

The cutting movement results from moving the

lever from the back edge of the tile towards its

front, while lightly pressing the lever.

WALL TILES

(single baked)

Lift the lever and position the break-off unit in the middle

of the tile. Press the lever down and the tile will break.

FLOOR TILES

(double-baked):

Sometimes these much harder tiles cannot be cut in two

by means of the break-off unit (K) on the tile cutting

machine.

In these cases after making the notch the tile must be

broken in two by tapping the underside of the tile with a

light hammer along the full length of the notch. This way

the break line will spread through the tile, and cause the

tile to break in two along the line. By means of the wing

nut (Q) the angle of the stop can be adjusted.

MAKING HOLES BY MEANS OF THE (HAND)

DRILL

1. Mount the drill attachment including the drill over

the centre of the hole in the base. It is important that

2 Ferm

Ferm 31

EXPLODED VIEW

SPARE PARTS LIST TCM-495

REF NR DESCRIPTION FERM NR

- SPARE CUTTING WHEEL TCA1001

A ELEVATING ARM 207809

E CLAMPING PLATE 207813

F CUTTER 207803

G CUTTER BRACKET 207802

I PIPE FIXTURE FOR LEVER 207807

K BREAKING HEAD 207805

Q WING NUT WITH WASHER 207819

R ANGLE INDICATOR 207820

WVU

T

S

N

P

O

L

I

H

C

B

A

D

M

E

F

K

G

Z

J

QR

Bedømmelse

Mere om denne brugsanvisning

Vi forstår, at det er rart at have en papirbrugsanvisning til din FERM TCM1001 Fliseskæremaskine. Du kan altid downloade brugsanvisningen fra vores hjemmeside og selv printe den. Hvis du gerne vil have en original brugsanvisning, anbefaler vi, at du kontakter FERM. De kan muligvis levere en original brugsanvisning. Leder du efter brugsanvisningen til din FERM TCM1001 Fliseskæremaskine på et andet sprog? Vælg dit foretrukne sprog på vores hjemmeside, og søg efter modelnummeret for at se, om vi har det tilgængeligt.

Specifikationer

Alle brugsanvisninger til FERM Fliseskæremaskiner
Flere brugsanvisninger til Fliseskæremaskiner

Ofte stillede spørgsmål om FERM TCM1001 Fliseskæremaskine

Vores support-team søger efter nyttige produktoplysninger og svar på ofte stillede spørgsmål. Hvis du finder urigtigheder i vores ofte stillede spørgsmål, må du meget gerne lade os det vide ved at bruge vores kontaktformular.

Relaterede produkter

Brugsanvisning

FERM TCM1010 Fliseskæremaskine

Brugsanvisning

FERM TCM1007 Fliseskæremaskine

Brugsanvisning

FERM TCM1006 Fliseskæremaskine

Brugsanvisning

FERM TCM1002 Fliseskæremaskine

Brugsanvisning

FERM TCM1003 Fliseskæremaskine

Brugsanvisning

Einhell TE-TC 620/1 U Fliseskæremaskine

Brugsanvisning

Atika ST 200 Fliseskæremaskine

Brugsanvisning

Carat Caracoup Fliseskæremaskine

Relaterede kategorier