Home > Have & Terrasse > Buskryddere > Ryobi Buskryddere > Ryobi RBC30SBSB Buskrydder

Brugsanvisning Ryobi RBC30SBSB Buskrydder

Har du brug for en brugsanvisning til din Ryobi RBC30SBSB Buskrydder? Nedenfor kan du se og downloade PDF-brugsanvisningen gratis på Dansk. Dette produkt har i øjeblikket 0 ofte stillede spørgsmål, 0 kommentarer og har 0 stemmer. Hvis dette ikke er den brugsanvisning, du ønsker, bedes du kontakte os.

Er dit produkt defekt, uden at brugsanvisningen har en løsning på problemet? Tag til en Repair Café, og få gratis reparation.

Brugsanvisning

Assembly

ATTACHING THE HANDLE

(Fig. 2a)

■ Remove the bolts and bracket from the front handle.

■ Place the handle bar.

NOTE: The throttle trigger must be mounted to the operator's

right side.

■ Replace the bolts and bracket.

■ Adjust the handle bar for best operator control and comfort.

■ Tighten the two bolts securely with the combination wrench

supplied.

ATTACHING THE BLADE GUARD AND GRASS

DEFLECTOR

Blade guard

(Fig. 2b)

■ To attach the blade deflector to the mounting bracket, align the

screw holes on the blade deflector to the bolts on the mounting

bracket.

■ Using the combination wrench supplied, tighten the two bolts

securely.

WARNING:

– The blade deflector should remain fitted to the product at

all times.

– When using the line trimmer bump head, the grass deflector

must be attached to the blade guard.

– When using the brushcutter blade, the grass deflector must

be removed from the blade guard.

Grass deﬂ ector

(Fig 2b)

■ To attach the grass deflector to the blade deflector, align the 3

screws on the grass deflector to the screw holes on the blade

deflector.

■ Using the combination wrench supplied, tighten the two bolts

securely.

NOTE: When using the line trimmer bump head, the grass

deflector must be attached to the blade guard.

INSTALLING THE REELEASY™ LINE TRIMMER HEAD

(Fig. 2c)

■ Stop the engine and disconnect the spark plug wire.

■ Remove the bump head from the drive connector.

■ Open the ReelEasy™ Line Trimmer Head by depressing the

latches on each side.

NOTE: The contents of the line trimmer head are spring loaded,

so keep your other hand over the line trimmer head cover while

depressing the latches.

■ Remove the line trimmer head cover, bump knob, and line spool

and set aside.

■ Place the cutting head housing on the drive shaft.

■ Make sure the housing is fully seated.

■ Install the hex bolt to secure the line trimmer head to the drive

shaft.

■ Tighten by using the hex-shaped opening on the inside of the

bump knob.

NOTE: Only use the bump knob to tighten the bolt. The use of

other tools may allow over tightening of the bolt, which could

damage the line trimmer head.

■ Reinstall the bump head spring into the line trimmer head and

push down to seat.

■ Reinstall the line spool.

■ For the curved shaft attachment with the ReelEasy™ cutting

head the spool should be placed so “For curved shaft” is visible

on the line spool.

■ Replace the bump knob by inserting it into the centre of the

line spool.

■ Replace the line trimmer head cover, aligning latches with

openings in the line trimmer head.

■ Press cover and line trimmer head together until both latches

snap into openings securely.

■ Install line as described in the next section of this manual.

INSTALLING LINE IN REELEASY™ LINE TRIMMER

HEAD

(Fig. 2c)

■ Use a 2.4 mm diameter monofilament string.

■ Stop the engine and disconnect the spark plug wire.

■ Cut one piece of string approximately 6 m in length.

■ Rotate the knob on the string head until the line on knob aligns

with the arrows on the top of string head.

■ Insert one end of the string into the eyelet located on the side of

the string head and push until string comes out through eyelet

on the other side.

■ Continue to push string through the string head until the middle

section of the string is inside the string head and string outside

the string head is evenly divided on each side.

■ Rotate the knob on the line trimmer head to wind the line.

■ If using a curved shaft attachment, the knob should be rotated

counterclockwise.

■ Wind the string until approximately 20 cm remains protruding

from the string head.

■ Replace the spark plug boot.

ATTACHING THE SHOULDER STRAP

(Fig. 2d)

■ Connect the latch on the shoulder strap to the strap hanger.

■ Adjust the strap hanger to a comfortable position.

NOTE: Always use the shoulder strap/harness with your unit.

CONVERTING FROM STRING TRIMMER TO

BRUSHCUTTER

(Fig. 2e)

Bedømmelse

Fortæl os, hvad du synes om Ryobi RBC30SBSB Buskrydder ved at lave en produktbedømmelse. Vil du dele dine oplevelser med dette produkt eller stille et spørgsmål? Skriv en kommentar nederst på siden.

Er du tilfreds med Ryobi RBC30SBSB Buskrydder?
Ja Ingen

Vær den første til at bedømme dette produkt

0 stemmer

Deltag i samtalen om dette produkt

Her kan du dele, hvad du synes om Ryobi RBC30SBSB Buskrydder. Hvis du har et spørgsmål, skal du først læse brugsanvisningen omhyggeligt. Anmodning om en brugsanvisning kan ske ved at bruge vores kontaktformular.

Mere om denne brugsanvisning

Vi forstår, at det er rart at have en papirbrugsanvisning til din Ryobi RBC30SBSB Buskrydder. Du kan altid downloade brugsanvisningen fra vores hjemmeside og selv printe den. Hvis du gerne vil have en original brugsanvisning, anbefaler vi, at du kontakter Ryobi. De kan muligvis levere en original brugsanvisning. Leder du efter brugsanvisningen til din Ryobi RBC30SBSB Buskrydder på et andet sprog? Vælg dit foretrukne sprog på vores hjemmeside, og søg efter modelnummeret for at se, om vi har det tilgængeligt.