Brugsanvisning Rexel LV340HS Lamineringsmaskine

Brugsanvisning

Operating Instructions

LV 250HS (A4) LV 340HS (A3)

A. Power Switch

B. ‘On’ light

C. ‘Ready’ light

D. Pouch/temperature setting

E. Entry Slot

F. Entry Guides

G. Exit slot

H. Release button

IMPORTANT SAFEGUARDS

When using electrical appliances, basic precautions

should always be followed to reduce the risk of

electric shock and injury, including the following:

1. Carefully read all instructions

2. Always unplug the appliance when not in use or

before cleaning.

3. Extreme caution to be taken when appliance is

used by, or near to, children or invalids.

4. To protect against risk of electrical hazards, do

not immerse power cord, plug, or appliance in

water or other liquids.

5. Do not insert any metal objects, e.g. scissors, or

foreign objects into the entry or exit areas of the

machine. Do not laminate metallic objects.

6. Do not operate the appliance with a damaged

power cord or plug, or after the appliance

malfunctions, has been dropped or is damaged

in any manner.

7. The plug on the power cord is the disconnect

device.

8. The equipment should be installed near the

outlet socket and the socket should be easily

accessible.

OPERATION

Before you use your LV Laminating machine for the

first time, it is recommended that you familiarise

yourself with the machine’s operation and controls.

Check the results using a range of sample sheets of

paper before laminating your valuable original

documents.

IMPORTANT

1. It is important that you do not use a Carrier with

this machine. This can result in the laminator

becoming jammed or failing to run. This is an

operator fault and is not covered by a

manufacturer’s warranty. (A carrier is made from

folded card and is supplied with most packs of

pouches).

2. Do not attempt to laminate items which are too

thick for your laminator i.e. the total thickness

including the pouch must not exceed 0.8mm.

HOT LAMINATING

1. Plug the laminator into a convenient power

socket

2. Switch on the power switch ( I ) , the Red light

will illuminate to indicate that the power is on

3. Select the appropriate temperature/pouch

setting for the thickness of pouch.

4. The laminator will pre-heat for approximately 4-5

minutes.

5. Whilst the laminator is pre heating, you can

prepare your item to be laminated by placing it

centrally into the correct sized pouch, leaving

the sealed edge intact.

6. When the required temperature is reached the

Green light will come on.

7. Gently insert the pouch, sealed edge first,

squarely between the entry guides into the front

of the laminator until it engages with automatic

feed rollers.

8. The pouch will move through the unit and exit at

rear.

9. During the laminating process the Green light

may go off as heat is absorbed by the laminate.

Always wait until the Green light is on before

laminating your next document.

10. Always turn your laminator OFF after use. ( O )

RELEASE FUNCTION

CAUTION: Do not try to force the pouch into

the laminator or try to pull the pouch out. This will

damage (and could break) the laminator as well as

not allowing for proper processing of the laminating

pouch.

There is a release button at the back on the left side

of the machine (H). IF you need to retrieve a

document during lamination:

1. Stop the machine by turning the power off (O).

2. Press the release button and hold it down.

3. With the other hand gently pull the pouch and

document out of the front of the machine.

4. If the pouch has gone completely into the

machine and is not sticking out of the front or

back, there is nothing you can do. Do not try to

open the machine. This can be dangerous and

will invalidate the warranty.

PHOTO LAMINATING

1. Your Rexel LV Laminator will laminate

photographs without the need for special

pouches. Photographs have a sealed plastic

surface that can produce disappointing results

on some laminators as the adhesive will show

as bubbles on the surface of the photograph.

2. Heavily coloured inkjet copies and varnished

printed pages will also have excellent results on

this laminator with standard pouches.

COLD LAMINATING

1. Select cold setting on the temperature dial.

2. Use ‘cold’ or ‘self-seal’ pouches

3. Remember, when the machine is cold the

temperature is correct to process ‘cold’ or ‘self-

seal’ pouches. The green ready light does not

illuminate for the cold setting.

CAUTION: Remember if you have been hot

laminating and then wish to Cold laminate the

machine will have to cool for at least 1 hour before

laminating can commence. Never use ‘self-seal’

pouches on a hot setting, as they will be spoilt along

with the document inside.

HELPFUL HINTS

1. The hot lamination process achieves the

required result by bonding into the surface of

your document. Once you have laminated your

document it cannot be retrieved.

2. Do not attempt to hot laminate heat sensitive

documents such as thermal paper, wax based

inks etc.

3. If the laminated document has a milky

appearance, you may need to process it again

at a higher temperature.

4. If the laminated document is ridged and hard it

has probably been laminated too hot, and you

should put other laminates through at a lower

setting.

5. If in doubt, start at a lower temperature and if

the laminate does not bond to the document

(appears cloudy) then repeat using a higher

temperature.

6. If air pockets develop during processing, use a

small sharp needle or pin to gently puncture

pockets and process again.

7. Do not handle the inside of the laminating pouch

moisture from your hands could impair the

processing quality.

CARE AND CLEANING

This personal laminator is for low volume use only.

No servicing other than external cleaning should be

performed on the machine. Do not immerse in

water.

To reduce risk of electric shock, do not remove

the base.

• Never clean with scouring powders or hand

implements.

• Wipe clean with a soft cloth

SERVICE AND REPAIRS

Do not attempt to repair the machine yourself

as there are no serviceable components within

the machine.

Never open up the machine

Repair should only be carried out by an

authorised service representative.

TECHNICAL SPECIFICATION

WARRANTY

This machine is guaranteed for 24 months from the

date of purchase – Rexel will repair or replace the

laminator at their discretion.

This does not affect your statutory rights.

Please contact your supplier if you experience any

problems.

Technical Specifications

Model LV250HS LV350HS

Maximum Pouch Size A4 /9" A3 / 12"

Minimum Pouch Size Credit card size (54x86mm)

Maximum Pouch Pouch sizes up to A7 =

Thickness 2 x 180 (360) micron

Maximum Pouch Pouch sizes above A7 =

Thickness 2 x 125 (250) micron

Power Supply 230V 115V 230V 115V

50Hz 60Hz 50Hz 60Hz

Maximum Power 350W 300W 450W 300W

Consumption

Weight 2.94Kg 3.7Kg

Packed Weight 3.59Kg 4.45Kg

GB

LV250_340HS_UserGuide.qxd 2/20/03 10:50 AM Page 18

Bedømmelse

Mere om denne brugsanvisning

Vi forstår, at det er rart at have en papirbrugsanvisning til din Rexel LV340HS Lamineringsmaskine. Du kan altid downloade brugsanvisningen fra vores hjemmeside og selv printe den. Hvis du gerne vil have en original brugsanvisning, anbefaler vi, at du kontakter Rexel. De kan muligvis levere en original brugsanvisning. Leder du efter brugsanvisningen til din Rexel LV340HS Lamineringsmaskine på et andet sprog? Vælg dit foretrukne sprog på vores hjemmeside, og søg efter modelnummeret for at se, om vi har det tilgængeligt.

Specifikationer

Alle brugsanvisninger til Rexel Lamineringsmaskiner
Flere brugsanvisninger til Lamineringsmaskiner

Relaterede produkter

Brugsanvisning

Rexel LP35HS Lamineringsmaskine

Brugsanvisning

Rexel LV250HS Lamineringsmaskine

Brugsanvisning

Rexel Style A3 Lamineringsmaskine

Brugsanvisning

Rexel Style A4 Lamineringsmaskine

Brugsanvisning

Rexel LP25HS Lamineringsmaskine

Brugsanvisning

Leitz iLAM Touch A3 Lamineringsmaskine

Brugsanvisning

GBC Fusion Plus 6000L Lamineringsmaskine

Brugsanvisning

United Office IAN 390956 Lamineringsmaskine

Relaterede kategorier