Brugsanvisning Powerworks PD60PS Kædesav

Brugsanvisning

English (original instructions)

EN

DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET

Do not use any attachments or accessories not

recommended by The manufacture of this product. The

use of attachments or accessories not recommended

can result in serious personal injury.

STARTING AND STOPPING See Figure 5

TO START THE MOTOR:

 Fit the battery pack into the pole saw.

 Press and hold the switch lock. This makes the switch

trigger operational.

 Press and hold the switch trigger, release the switch

lock and continue to squeeze the switch trigger for

continued operation.

TO STOP THE MOTOR:

 Release the switch trigger.

PREPARATION FOR CUTTING

 Wear non-slip gloves for maximum grip and

protection.

 Maintain a proper grip on the unit whenever the motor

is running. Use your right hand to firmly grip the rear

handle while your left hand has a firm grip on the pole

shaft.

 Hold unit firmly with both hands. Always keep your

left hand on the pole shaft and your right hand on the

rear handle, so your body is to the left of the chain

line. Never use a left-handed (cross handed) grip, or

any stance that places your body or arm across the

chain line.

 Never stand directly under the limb you are cutting.

 Be certain the collars are fully tightened before

operating equipment; check them periodically for

tightness during use to avoid serious injury.

BASIC CUTTING PROCEDURE

See Figures 6-7

Follow the steps below to prevent damage to tree or

shrub bark. Do not use a back-and-forth sawing motion.

 Make a shallow first cut (1/4 of limb diameter) on the

underside of the limb close to the main limb or trunk.

 Make a second cut from the top side of the limb

outboard from the first cut. Continue the cut through

the limb until the limb separates from the tree. Be

prepared to balance the weight of the tool when the

limb falls.

 Make a final cut close to trunk.

NOTE: For second and final cuts (from top of limb or

branch), hold front cutting guide against the limb being

cut. This will help steady the limb and make it easier to

cut. Allow chain to cut for you; exert only slight downward

pressure. If you force the cut, damage to the bar, chain,

or motor can result.

 Release the trigger as soon as the cut is completed.

Failure to follow proper cutting procedures will result

in the bar and chain binding and becoming pinched or

trapped in the limb. If this should happen:

 Stop the motor and remove the battery pack.

 If the limb can be reached from the ground, lift the

limb while holding the saw. This should release the

“pinch” and free the saw.

 If the saw is still trapped, call a professional for

assistance

LIMBING AND PRUNING See Figure 8-9

This unit is designed for trimming small branches and

limbs up to 15 cm in diameter. For best results, observe

the following precautions

 Plan the cut carefully. Be aware of the direction in

which the branch will fall.

 Branches may fall in unexpected directions. Do not

stand directly under the branch being cut.

 The most typical cutting application is to position

the unit at an angle of 60° or less, depending on the

specific situation. As the angle of the pole saw shaft to

ground increases, the difficulty of making the first cut

(from the underside of limb) increase.

 Remove long branches in several stages.

 Cut lower branches first to allow the top branches

more room to fall.

 Work slowly, keeping both hands on the saw with a

firm grip. Maintain secure footing and balance.

 Keep the tree between you and the chain while

limbing. Cut from side of tree opposite branch you are

cutting.

 Do not cut from a ladder; this is extremely dangerous.

Leave this operation for professionals.

 Do not make the flush cut next to the main limb or

trunk until you have cut off the limb further out to

reduce the weight. Following proper cutting procedure

will prevent stripping the bark from the main member.

 Do not use the pole saw for felling or bucking

 To prevent electrocution, do not operate within 15m of

overhead electrical lines.

 Keep bystanders at least 15m away.

MAINTENANCE

REPLACING THE BAR AND CHAIN See Figure

10-12

 Remove the lock knob and drivecase cover.

 The bar contains a bar stud slot that fits over the bar

stud. The bar also contains a chain tension pin hole

which fits over the chain tensioning pin.

3

Bedømmelse

Mere om denne brugsanvisning

Vi forstår, at det er rart at have en papirbrugsanvisning til din Powerworks PD60PS Kædesav. Du kan altid downloade brugsanvisningen fra vores hjemmeside og selv printe den. Hvis du gerne vil have en original brugsanvisning, anbefaler vi, at du kontakter Powerworks. De kan muligvis levere en original brugsanvisning. Leder du efter brugsanvisningen til din Powerworks PD60PS Kædesav på et andet sprog? Vælg dit foretrukne sprog på vores hjemmeside, og søg efter modelnummeret for at se, om vi har det tilgængeligt.

Specifikationer

Alle brugsanvisninger til Powerworks Kædesave
Flere brugsanvisninger til Kædesave

Ofte stillede spørgsmål om Powerworks PD60PS Kædesav

Vores support-team søger efter nyttige produktoplysninger og svar på ofte stillede spørgsmål. Hvis du finder urigtigheder i vores ofte stillede spørgsmål, må du meget gerne lade os det vide ved at bruge vores kontaktformular.

Relaterede produkter

Brugsanvisning

Powerworks PD60CS40 Kædesav

Brugsanvisning

Parkside IAN 434664 Kædesav

Brugsanvisning

Worx WA0307 Kædesav

Brugsanvisning

Worx WG349E.9 Kædesav

Brugsanvisning

Atika KS 1800/35 Kædesav

Brugsanvisning

EGO CS1410E Kædesav

Brugsanvisning

Husqvarna 450e II Kædesav

Brugsanvisning

Bosch UniversalChain 40 Kædesav

Relaterede kategorier