Brugsanvisning Powerworks PD60CS40 Kædesav

Brugsanvisning

English (original instructions)

EN

DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET

21. Chain drive links

22. Cutter

23. Felling direction

24. Danger zone

25. Escape route

26. Direction of fall

27. Notch

28. Felling back cut

29. Hinge

30. Limb cut

31. Keep work off ground leave support limbs

until log is cut

32. Log supported along the entire length

33. Cut from top (over buck) avoid cutting

earth

34. Log supported one end

35. Under buck

36. Over buck

37. Log supported both ends

38. Bucking a log

39. Stand on uphill side when cutting because

log may roll

ASSEMBLY

This chain saw requires no assembly, but user

should know how to assemble the guide bar

and saw chain. Check the chain tensioning

and add oil as described later in this manual

before each operation.

ASSEMBLING THE GUIDE BAR AND SAW

CHAIN

See figure 2 - 7

Make sure remove the battery pack from the

unit. Wear protective gloves.

 Unscrew the sprocket cover tighten knob

and remove the sprocket cover.

 The saw chain should face in the direction

of chain rotation. If they face backwards,

turn the loop over.

 Place the chain drive links into the bar

groove.

 Position the chain so there is a loop at the

back of the bar.

 Hold the chain in position on the bar and

place the loop around the sprocket and

make sure it is correctly mounted. Make

sure the bar hole ts well with bolt for saw

chain tension.

 Replace the sprocket cover, turn the

chain tension adjust knob clockwise until

the saw chain is properly tensioned. The

guide bar must then be pushed upwards,

check chain tension again, do not tension

the chain too tight.

 After the chain is well-tensioned, tighten

the knob again.

NOTE: The saw chain is properly tensioned if,

in the middle of the guide bar, it can be lifted

3mm to 4mm from the edge of the guide bar.

Start the saw again with a new saw chain,

allowing it to run-in for 2~3 minutes.

WARNING

After the run-in time, check the chain tension

and retighten the chain if necessary.

OPERATION

For complete charging instructions,

refer to the Operator’s Manuals for your

Greenworks Tools battery pack and

charger models.

NOTE: To avoid serious personal injury,

always remove the battery pack and keep

hands clear of the lock-out button when

carrying or transporting the tool.

BEFORE EACH USE CHECK THE CHAIN

TENSION

2

Bedømmelse

Mere om denne brugsanvisning

Vi forstår, at det er rart at have en papirbrugsanvisning til din Powerworks PD60CS40 Kædesav. Du kan altid downloade brugsanvisningen fra vores hjemmeside og selv printe den. Hvis du gerne vil have en original brugsanvisning, anbefaler vi, at du kontakter Powerworks. De kan muligvis levere en original brugsanvisning. Leder du efter brugsanvisningen til din Powerworks PD60CS40 Kædesav på et andet sprog? Vælg dit foretrukne sprog på vores hjemmeside, og søg efter modelnummeret for at se, om vi har det tilgængeligt.

Specifikationer

Alle brugsanvisninger til Powerworks Kædesave
Flere brugsanvisninger til Kædesave

Ofte stillede spørgsmål om Powerworks PD60CS40 Kædesav

Vores support-team søger efter nyttige produktoplysninger og svar på ofte stillede spørgsmål. Hvis du finder urigtigheder i vores ofte stillede spørgsmål, må du meget gerne lade os det vide ved at bruge vores kontaktformular.

Relaterede produkter

Brugsanvisning

Powerworks PD60PS Kædesav

Brugsanvisning

Stihl MS 182 Kædesav

Brugsanvisning

Parkside PBKS 53 B3 Kædesav

Brugsanvisning

Worx WG324E.2 Kædesav

Brugsanvisning

Bosch AKE 35 Kædesav

Brugsanvisning

Atika KS 1800/35 Kædesav

Brugsanvisning

Solo 6646 Kædesav

Brugsanvisning

AL-KO CS 36 Li Kædesav

Relaterede kategorier