Brugsanvisning Kampa Air Shelter 400 Telt

Brugsanvisning

EN

4445103460 5

Setting up the shelter

!

A

I

Keep the following tips in mind while setting up the shelter:

• The figures provide a general overview of the set-up. The actual set-up

will vary slightly based on the model of shelter.

• Get help. The set-up is easier with more people.

• After standing the shelter upright, check the corner pegs and re-peg

if necessary. The groundsheet on the inside should be taut and in a

rectangular shape.

• Peg the guy lines so that the shelter is under tension without distorting

the shape.

• Check the guy lines from time to time to ensure adequate tension, if

necessary use the runners to adjust.

Set up the shelter as follows:

1. To protect the shelter from dirt and damage, lay down a groundsheet

or footprint before unpacking.

2. Unpack the shelter.

3. Separate and identify the different components.

4. Proceed as shown to set up the shelter (fig. 1, page 3 to fig. 6,

page 3).

Dismantling the shelter

A

1. Reverse the set up procedure.

2. Push the poles out of the sleeves, do not pull.

3. Ensure that all parts are clean before packing in the carry bag.

4. If the shelter is wet or damp, dry fully as soon as possible.

Cleaning and maintenance

A

1. If necessary, clean the product with clean water and a soft brush.

2. Apply impregnation against water and UV radiation before each trip.

Storing the shelter

I

1. Clean the shelter.

2. Air fully and ensure the shelter is totally dry before packing away.

3. Store in a well ventilated dry place.

Troubleshooting

I

Repairing a puncture in the air pole

If the air pole loses air, proceed as follows:

1. Unzip the outer sleeve holding the air pole.

2. If installed, close isolation valves.

3. Remove the air pole.

4. Deflate the air pole.

5. Unzip the protective sleeve to expose the inflatable tube.

6. Blow some air into the inflatable tube.

7. Submerge the tube in water.

8. Locate the puncture.

9. Use repair tape and repair solution to seal the hole.

10. Zip the inflatable tube back into the protective sleeve.

11. Zip the air pole back into the outer sleeve.

CAUTION! Risk of injury and material damage

• Do not use any type of compressor designed to inflate

car tires.

• Only inflate the air poles into the green zone of the

pressure gauge of the supplied hand pump (7 –

8 psi/0.48 – 0.55 bar).

NOTICE! Material damage

Do not open or close the zippers by force.

NOTE

• The shelter comes with general purpose pegs. These

will be suitable for many sites but for some types of

ground special pegs will be needed. Ask your dealer.

• Drive the pegs at a 45° angle away from the shelter into

the ground.

• Peg each guy line in-line with the seam it starts from.

NOTICE! Material damage

Do not use force when dismantling the shelter. Otherwise

you might damage any material.

NOTICE! Damage hazard

• Do not use sharp or hard objects or cleaning agents for

cleaning.

• Do not use alcohol based materials, chemicals, soap

and detergents for cleaning.

• Remove bird droppings and tree resin as soon as

possible to avoid permanent damage to the material.

NOTE

• Fully set up the shelter for cleaning.

• Choose a sunny day for cleaning to ensure the material

will dry thoroughly.

NOTE

• During first exposure to water there may be some

moisture at the seams. Through this moisture the threads

will swell and fill the holes that are created in the sewing

process.

• A fully equipped spare parts kit should include:

– Waterproofer

– Repair tape and repair solution

– Silicone spray for the zippers

– Spare pegs

Problem Solution

Shelter only inflates with difficulties ➤ Check that the valve is fully screwed

into the air pole.

➤ Check if the inflation tube is twisted at

the valve.This may be indicated by

noise. Untwist the inflation tube

Air leak ➤ Check that the valve is fully screwed

into the air pole and the ring seal is in

place.

➤ Check that the cap of the valve is done

up tightly.

➤ Check for punctures, see chapter

“Repairing a puncture in the air pole”

on page 5.

Water leak

➤ Check for leaky seams, damaged

tapings and moist areas.

➤ If you find any leaks, apply seam

sealant.

Rip in the fabric

➤ Use repair tape to seal the fabric.

➤ Have repairs carried out by an

authorized specialist.

KampaAirShelter200-300-400_IOM_4445103460_EMEA16_20xx-xx-xx.book Seite 5 Montag, 4. Oktober 2021 12:30 12

Bedømmelse

Mere om denne brugsanvisning

Vi forstår, at det er rart at have en papirbrugsanvisning til din Kampa Air Shelter 400 Telt. Du kan altid downloade brugsanvisningen fra vores hjemmeside og selv printe den. Hvis du gerne vil have en original brugsanvisning, anbefaler vi, at du kontakter Kampa. De kan muligvis levere en original brugsanvisning. Leder du efter brugsanvisningen til din Kampa Air Shelter 400 Telt på et andet sprog? Vælg dit foretrukne sprog på vores hjemmeside, og søg efter modelnummeret for at se, om vi har det tilgængeligt.

Specifikationer

Alle brugsanvisninger til Kampa Telte
Flere brugsanvisninger til Telte

Ofte stillede spørgsmål om Kampa Air Shelter 400 Telt

Vores support-team søger efter nyttige produktoplysninger og svar på ofte stillede spørgsmål. Hvis du finder urigtigheder i vores ofte stillede spørgsmål, må du meget gerne lade os det vide ved at bruge vores kontaktformular.

Relaterede produkter

Brugsanvisning

Kampa Mersea 4 Telt

Brugsanvisning

Kampa Brighton 5 Telt

Brugsanvisning

Kampa Brighton 2 Telt

Brugsanvisning

Kampa Brean 3 Air Telt

Brugsanvisning

Kampa Brighton 4 Telt

Brugsanvisning

Kampa Air Shelter 200 Telt

Brugsanvisning

Kampa Touring AIR RH Telt

Brugsanvisning

Kampa Touring AIR TC RH Telt

Relaterede kategorier