Home > Gør-Det-Selv > Vinkelslibere > Hikoki Vinkelslibere > Hikoki G 18DBBL Vinkelsliber

Brugsanvisning Hikoki G 18DBBL Vinkelsliber

Har du brug for en brugsanvisning til din Hikoki G 18DBBL Vinkelsliber? Nedenfor kan du se og downloade PDF-brugsanvisningen gratis på Dansk. Dette produkt har i øjeblikket 4 ofte stillede spørgsmål, 0 kommentarer og har 0 stemmer. Hvis dette ikke er den brugsanvisning, du ønsker, bedes du kontakte os.

Er dit produkt defekt, uden at brugsanvisningen har en løsning på problemet? Tag til en Repair Café, og få gratis reparation.

Brugsanvisning

English

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal to

another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, ﬂ ush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or

burns.

6) Service

a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

PRECAUTION

Keep children and inﬁ rm persons away.

When not in use, tools should be stored out of reach of

children and inﬁ rm persons.

SAFETY WARNINGS COMMON FOR

GRINDING OR ABRASIVE CUTTING-

OFF OPERATIONS

a) This power tool is intended to function as a

grinder or cut-oﬀ tool. Read all safety warnings,

instructions, illustrations and speciﬁ cations

provided with this power tool.

Failure to follow all instructions listed below may result in

electric shock, ﬁ re and/or serious injury.

b) Operations such as sanding, wire brushing or

polishing are not recommended to be performed

with this power tool.

Operations for which the power tool was not designed

may create a hazard and cause personal injury.

c) Do not use accessories which are not speciﬁ cally

designed and recommended by the tool

manufacturer.

Just because the accessory can be attached to your

power tool, it does not assure safe operation.

d) The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool.

Accessories running faster than their rated speed can

break and ﬂ y apart.

e) The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool.

Incorrectly sized accessories cannot be adequately

guarded or controlled.

f) Threaded mounting of accessories must match the

grinder spindle thread. For accessories mounted

by ﬂ anges, the arbour hole of the accessory must

ﬁ t the locating diameter of the ﬂ ange.

Accessories that do not match the mounting hardware of

the power tool will run out of balance, vibrate excessively

and may cause loss of control.

g) Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for

chips and cracks, backing pad for cracks, tear or

excess wear, wire brush for loose or cracked wires.

If power tool or accessory is dropped, inspect for

damage or install an undamaged accessory. After

inspecting and installing an accessory, position

yourself and bystanders away from the plane of

the rotating accessory and run the power tool at

maximum no-load speed for one minute.

Damaged accessories will normally break apart during

this test time.

h) Wear personal protective equipment. Depending

on application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and workshop apron

capable of stopping small abrasive or workpiece

fragments.

The eye protection must be capable of stopping ﬂ ying

debris generated by various operations. The dust mask

or respirator must be capable of ﬁ ltrating particles

generated by your operation. Prolonged exposure to

high intensity noise may cause hearing loss.

i) Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment.

Fragments of workpiece or of a broken accessory may

ﬂ y away and cause injury beyond immediate area of

operation.

j) Hold the power tool by insulated gripping surfaces

only, when performing an operation where the

cutting tool may contact hidden wiring.

Contact with a “live” wire will also make exposed metal

parts of the power tool “live” and could give the operator

an electric shock.

k) Position the cord clear of the spinning accessory.

If you lose control, the cord may be cut or snagged

and your hand or arm may be pulled into the spinning

accessory.

l) Never lay the power tool down until the accessory

has come to a complete stop.

The spinning accessory may grab the surface and pull

the power tool out of your control.

m) Do not run the power tool while carrying it at your

side.

Accidental contact with the spinning accessory could

snag your clothing, pulling the accessory into your body.

n) Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electrical hazards.

o) Do not operate the power tool near ﬂ ammable

materials.

Sparks could ignite these materials.

p) Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution or shock.

KICKBACK AND RELATED

WARNINGS

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other accessory.

Pinching or snagging causes rapid stalling of the rotating

accessory which in turn causes the uncontrolled power tool

to be forced in the direction opposite of the accessory’s

rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by

the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing

the wheel to climb out or kick out. The wheel may either jump

0000Book̲G18DBBL.indb30000Book̲G18DBBL.indb3 2017/12/0113:15:442017/12/0113:15:44

Bedømmelse

Fortæl os, hvad du synes om Hikoki G 18DBBL Vinkelsliber ved at lave en produktbedømmelse. Vil du dele dine oplevelser med dette produkt eller stille et spørgsmål? Skriv en kommentar nederst på siden.

Er du tilfreds med Hikoki G 18DBBL Vinkelsliber?
Ja Ingen

Vær den første til at bedømme dette produkt

0 stemmer

Deltag i samtalen om dette produkt

Her kan du dele, hvad du synes om Hikoki G 18DBBL Vinkelsliber. Hvis du har et spørgsmål, skal du først læse brugsanvisningen omhyggeligt. Anmodning om en brugsanvisning kan ske ved at bruge vores kontaktformular.

Mere om denne brugsanvisning

Vi forstår, at det er rart at have en papirbrugsanvisning til din Hikoki G 18DBBL Vinkelsliber. Du kan altid downloade brugsanvisningen fra vores hjemmeside og selv printe den. Hvis du gerne vil have en original brugsanvisning, anbefaler vi, at du kontakter Hikoki. De kan muligvis levere en original brugsanvisning. Leder du efter brugsanvisningen til din Hikoki G 18DBBL Vinkelsliber på et andet sprog? Vælg dit foretrukne sprog på vores hjemmeside, og søg efter modelnummeret for at se, om vi har det tilgængeligt.

Specifikationer

Mærke	Hikoki
Model	G 18DBBL
Kategori	Vinkelslibere
Filtype	PDF
Filstørrelse	13.23 MB

Alle brugsanvisninger til Hikoki Vinkelslibere
Flere brugsanvisninger til Vinkelslibere

Ofte stillede spørgsmål om Hikoki G 18DBBL Vinkelsliber

Vores support-team søger efter nyttige produktoplysninger og svar på ofte stillede spørgsmål. Hvis du finder urigtigheder i vores ofte stillede spørgsmål, må du meget gerne lade os det vide ved at bruge vores kontaktformular.

På hvilke materialer kan man bruge en vinkelsliber? Verificeret

Vinkelslibere er mest velegnet til brug på metal eller sten. Maskinerne genererer meget varme og er derfor mindre velegnet til brug på træ eller plast.

Dette var nyttigt (63) Læs mere

Har jeg brug for høreværn, når jeg bruger en vinkelsliber? Verificeret

Ja du burde. Selv om støjmængden, der produceres af en vinkelsliber, kan variere mellem mærker og modeller, kan langvarig udsættelse for høj støj forårsage permanent høreskade. Derfor er det en god ide at bære høreværn.

Dette var nyttigt (16) Læs mere

Har jeg brug for øjenbeskyttelse, når jeg bruger en vinkelsliber? Verificeret

Ja. Små partikler kan flyve op under slibning. Når disse rammer et øje, kan de forårsage permanent øjenskade. Derfor er det altid nødvendigt at bære øjenbeskyttelse.

Dette var nyttigt (14) Læs mere

Kan jeg opbevare elværktøj i et skur eller garage? Verificeret

Generelt kan du opbevare elværktøj i et skur eller garage, selvom det nogle gange fryser der. Det er dog bedre for elværktøjets levetid at opbevare det på et tørt sted uden større temperaturudsving. I et skur eller garage kan temperaturforskelle medføre, at der dannes kondens, som kan give rust. Derudover holder værktøj, der kører på batterier, kortere og oplader ikke så godt ved meget lave temperaturer. For at være sikker på, hvordan dit elværktøj skal opbevares, skal du altid læse brugervejledningen grundigt.

Dette var nyttigt (4) Læs mere