Brugsanvisning Hikoki DV 20VB2 Slagboremaskine

Brugsanvisning

4

English

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package

contains the accessories listed in the below.

(1) Chuck wrench (Spec. only for keyed chuck) ................1

(2) Side handle ..................................................................1

(3) Depth gauge ................................................................1

Standard accessories are subject to change without notice.

APPLICATIONS

○ By combined actions of ROTATION and IMPACT:

Boring holes in hard materials (concrete, marble, granite,

tiles, etc.)

○ By ROTATIONAL action:

Boring holes in metal, wood and plastic.

SPECIFICATIONS

Voltage*

1

(110 V, 220 V, 230 V, 240 V)

Power input 790 W*

1

Speed range 1 2

No load

speed

Forward

rotation

0 – 1000 min

-1

0 – 3000 min

-1

Reverse

rotation

0 – 600 min

-1

0 – 1800 min

-1

Capacity

Steel

13 mm 8 mm

Concrete

20 mm 13 mm

Wood

40 mm 25 mm

Full-load impact rate

8000 min

-1

26000 min

-1

Weight*

2

2.5 kg

*1 Be sure to check the nameplate on product as it is subject

to change by areas.

*2 Weight: According to EPTA-Procedure 01/2003

NOTE

Due to HiKOKI’s continuing program of research and

development, the specifi cations herein are subject to

change without prior notice.

MOUNTING AND OPERATION

Action Figure Page

Fixing and removing side handle

199

Using depth stopper 2 99

Mounting and dismounting of the

bit (For keyed chuck)

399

Mounting and dismounting of the

bit (For keyless chuck Type A)*

1

499

Mounting and dismounting of the

bit (For keyless chuck Type B)*

2

599

Selecting rotation direction 6 100

Selecting the operating mode 7 100

Switch operation*

3

8 100

Locking-on the switch

9 100

Releasing the switch

10 100

Change rotation speed

11 101

Selecting accessories ― 102

Selecting the appropriate drill bit

○ When boring concrete or stone

Use the drill bits specifi ed in the Optional Accessories.

○ When boring metal or plastic

Use an ordinary metalworking drill bit.

○ When boring wood

Use ordinary woodworking drill bit.

However, when drilling 6.5 mm or smaller holes, use a

metalworking drill bit.

*1 Type A (Fig. 5)

(1) Mounting the bit

Turn the lock collar in the direction “AUF” and open the

chuck. After inserting the drill bit into the chuck as far it

will go, turn the lock collar in the “ZU” direction. Grip the

ring and close the chuck by turning the sleeve clockwise

as viewed from the front.

(2) Dismounting the bit

Turn the lock collar in the direction “AUF” to release the

chucking force. Grip the ring and open the chuck by

turning the sleeve counterclockwise.

*2 Type B (Fig. 6)

(1) Mounting the bit

Turn the sleeve counterclockwise and open the chuck.

After inserting the drill bit into the chuck as far it will go,

grip the ring and close the chuck by turning the sleeve

clockwise as viewed from the front.

(2) Dismounting the bit

Grip the ring and open the chuck by turning the sleeve

counterclockwise.

*3 CAUTION

If the L-side of push button is pressed for reverse bit

rotation, the stopper cannot be used.

MAINTENANCE AND INSPECTION

1. Inspecting the drill bits

Since use of an abraded drill bits will cause motor

malfunctioning and degraded effi ciency, replace the drill

bits with a new one or resharpening without delay when

abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes

For your continued safety and electrical shock protection,

carbon brush inspection and replacement on this tool

should ONLY be performed by a HiKOKI Authorized

Service Center.

5. Replacing supply cord

If the replacement of the supply cord is necessary, it

has to be done by HiKOKI Authorized Service Center to

avoid a safety hazard.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

0000Book̲DV20VB2.indb40000Book̲DV20VB2.indb4 2017/12/0410:48:172017/12/0410:48:17

Bedømmelse

Mere om denne brugsanvisning

Vi forstår, at det er rart at have en papirbrugsanvisning til din Hikoki DV 20VB2 Slagboremaskine. Du kan altid downloade brugsanvisningen fra vores hjemmeside og selv printe den. Hvis du gerne vil have en original brugsanvisning, anbefaler vi, at du kontakter Hikoki. De kan muligvis levere en original brugsanvisning. Leder du efter brugsanvisningen til din Hikoki DV 20VB2 Slagboremaskine på et andet sprog? Vælg dit foretrukne sprog på vores hjemmeside, og søg efter modelnummeret for at se, om vi har det tilgængeligt.

Specifikationer

Alle brugsanvisninger til Hikoki Slagboremaskiner
Flere brugsanvisninger til Slagboremaskiner

Ofte stillede spørgsmål om Hikoki DV 20VB2 Slagboremaskine

Vores support-team søger efter nyttige produktoplysninger og svar på ofte stillede spørgsmål. Hvis du finder urigtigheder i vores ofte stillede spørgsmål, må du meget gerne lade os det vide ved at bruge vores kontaktformular.

Relaterede produkter

Brugsanvisning

Hikoki DV 16V Slagboremaskine

Brugsanvisning

Hikoki DV 22V Slagboremaskine

Brugsanvisning

Hikoki D 13VL Slagboremaskine

Brugsanvisning

Hikoki DV 13SS Slagboremaskine

Brugsanvisning

Hikoki D 13VB3 Slagboremaskine

Brugsanvisning

Hikoki DV 20VD Slagboremaskine

Brugsanvisning

Bosch GBM 1600 RE Slagboremaskine

Brugsanvisning

Black and Decker BEH550-QS Slagboremaskine

Relaterede kategorier