Home > Gør-Det-Selv > Stiksave > Hikoki Stiksave > Hikoki CJ 18DSL Stiksav

Brugsanvisning Hikoki CJ 18DSL Stiksav

Name: Hikoki CJ 18DSL Stiksav
Brand: Hikoki
SKU: CJ 18DSL
Rating: 100 (1 reviews)

Har du brug for en brugsanvisning til din Hikoki CJ 18DSL Stiksav? Nedenfor kan du se og downloade PDF-brugsanvisningen gratis på Dansk. Dette produkt har i øjeblikket 4 ofte stillede spørgsmål, 0 kommentarer og har 1 stemme med en gennemsnitlig produktvurdering på 100/100. Hvis dette ikke er den brugsanvisning, du ønsker, bedes du kontakte os.

Er dit produkt defekt, uden at brugsanvisningen har en løsning på problemet? Tag til en Repair Café, og få gratis reparation.

Brugsanvisning

English

○ When the pilot lamp ﬂ ickers in red (at 0.2-seconds

intervals), check for and take out any foreign objects in

the charger’s battery connector. If there are no foreign

objects, it is probable that the battery or charger is

malfunctioning. Take it to your authorized Service

Center.

○ Since the built-in micro computer takes about 3

seconds to conﬁ rm that the battery being charged with

charger is taken out, wait for a minimum of 3 seconds

before reinserting it to continue charging. If the battery

is reinserted within 3 seconds, the battery may not be

properly charged.

○ Check the voltage of the in-car power source when

the pilot lamp ﬂ ickers in green (every 0.2 seconds)

continuously. (UC18YML2)

If the voltage is 12V or lower, it indicates that the car

battery has weakened and cannot be charged.

○ If the pilot lamp does not blink in red (every second) even

though the charger cord or cigarette lighter connecting

plug is connected to the power, it indicates that the

protection circuit of the charger may be activated.

Remove the cord or plug from the power and then

connect it again after 30 seconds or so. If this does

not cause the pilot lamp to blink in red (every second),

please take the charger to the HiKOKI Authorized

Service Center.

MOUNTING AND OPERATION

Action Figure Page

Removing and inserting the battery 1

181

Charging 2

181

Changing blades 3

181

Switch operation 4

181

Remaining battery indicator 5

181

Adjusting the orbital operation 6

181

Splinter guard 7

182

Mounting and dismounting the chip

cover

182

Housing the hexagonal bar wrench

182

Mounting the guide (sold separately)

and rectilinear cutting

182

Mounting the guide (sold separately)

and cutting a circle or a circular arc

182

Cutting metallic materials 12

182

Angular cutting 13

183

Pocket cutting 14

183

Concerning cutting of stainless steel

plates

183

Connecting with cleaner 16

183

Sub base 17

183

Selecting accessories ―

184

SELECTION OF BLADES

To ensure maximum operating eﬃ ciency and results, it is

very important to select the appropriate blade best suited to

the type and thickness of the material to be cut. The blade

number is engraved in the vicinity of the mounting portion

of each blade. Select appropriate blades by referring to

Table 3.

MAINTENANCE AND INSPECTION

CAUTION

Pull out battery before doing any inspection or

maintenance.

1. Inspecting the blade

Continued use of a dull or damaged blade will result in

reduced cutting eﬃ ciency and may cause overloading of

the motor. Replace the blade with a new one as soon as

excessive abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Cleaning on the outside

When the power tool is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric

solvents, gasoline or paint thinner, for they melt plastics.

5. Storage

Store the power tool in a place in which the temperature

is less than 40°C and out of reach of children.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

Important notice on the batteries for the HiKOKI

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when

the battery is disassembled and modiﬁ ed (such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee HiKOKI power tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the power tool, undismantled, with the GUARANTEE

CERTIFICATE

found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

0000Book̲CJ18DSL.indb70000Book̲CJ18DSL.indb7 2019/07/2518:54:372019/07/2518:54:37

Bedømmelse

Fortæl os, hvad du synes om Hikoki CJ 18DSL Stiksav ved at lave en produktbedømmelse. Vil du dele dine oplevelser med dette produkt eller stille et spørgsmål? Skriv en kommentar nederst på siden.

Er du tilfreds med Hikoki CJ 18DSL Stiksav?
Ja Ingen

100%

1 stemme

Deltag i samtalen om dette produkt

Her kan du dele, hvad du synes om Hikoki CJ 18DSL Stiksav. Hvis du har et spørgsmål, skal du først læse brugsanvisningen omhyggeligt. Anmodning om en brugsanvisning kan ske ved at bruge vores kontaktformular.

Mere om denne brugsanvisning

Vi forstår, at det er rart at have en papirbrugsanvisning til din Hikoki CJ 18DSL Stiksav. Du kan altid downloade brugsanvisningen fra vores hjemmeside og selv printe den. Hvis du gerne vil have en original brugsanvisning, anbefaler vi, at du kontakter Hikoki. De kan muligvis levere en original brugsanvisning. Leder du efter brugsanvisningen til din Hikoki CJ 18DSL Stiksav på et andet sprog? Vælg dit foretrukne sprog på vores hjemmeside, og søg efter modelnummeret for at se, om vi har det tilgængeligt.

Specifikationer

Mærke	Hikoki
Model	CJ 18DSL
Kategori	Stiksave
Filtype	PDF
Filstørrelse	15.35 MB

Alle brugsanvisninger til Hikoki Stiksave
Flere brugsanvisninger til Stiksave

Ofte stillede spørgsmål om Hikoki CJ 18DSL Stiksav

Vores support-team søger efter nyttige produktoplysninger og svar på ofte stillede spørgsmål. Hvis du finder urigtigheder i vores ofte stillede spørgsmål, må du meget gerne lade os det vide ved at bruge vores kontaktformular.

Hvilke materialer kan jeg anvende min stiksav til? Verificeret

Da savklingerne kan skiftes ud, kan stiksave bruges til næsten ethvert materiale. Stiksave anvendes for det meste til at save rundinger og hjørner med.

Dette var nyttigt (442) Læs mere

Har jeg brug for øjenbeskyttelse, når jeg bruger et stiksav? Verificeret

Ja. Små partikler kan flyve op under savning. Når disse rammer et øje, kan de forårsage permanent øjenskade. Derfor er det altid nødvendigt at bære øjenbeskyttelse.

Dette var nyttigt (216) Læs mere

Kan jeg opbevare elværktøj i et skur eller garage? Verificeret

Generelt kan du opbevare elværktøj i et skur eller garage, selvom det nogle gange fryser der. Det er dog bedre for elværktøjets levetid at opbevare det på et tørt sted uden større temperaturudsving. I et skur eller garage kan temperaturforskelle medføre, at der dannes kondens, som kan give rust. Derudover holder værktøj, der kører på batterier, kortere og oplader ikke så godt ved meget lave temperaturer. For at være sikker på, hvordan dit elværktøj skal opbevares, skal du altid læse brugervejledningen grundigt.

Dette var nyttigt (64) Læs mere

Skal jeg have høreværn på, når jeg bruger en stiksav? Verificeret

Ja du burde. Selvom mængden af støj produceret af en stiksav kan variere mellem mærker og modeller, kan langvarig eksponering for høj støj forårsage permanent høreskade. Derfor er det en god idé at have høreværn på.

Dette var nyttigt (41) Læs mere