Brugsanvisning FERM CDM1005 Bore-skruemaskine

Brugsanvisning

dots between the figures to define intermediate

settings (16 in total).

• You should preferably choose as low a setting as

possible when using the screwdriver. Select a higher

setting if the motor slips.

DRIVING AND REMOVING SCREWS

• Set the direction reversing switch (6) to position 'R'

in order to drive screws.

• Set the direction reversing switch to position 'L' in

order to remove screws.

DRILLING

• Rotate the torque adjustment ring (3) to the drilling

position.

Ensure that the direction reversing switch (6) is

always set to 'R' during drilling.

SWITCHING THE DEVICE ON AND OFF

Fig. A

• Depress the on/off switch (1). It regulates the speed

of the appliance by transmitting power to the switch.

• Release the on/off switch (1) to halt the drill chuck

immediately which will no longer run on.

• Move the direction reversing switch (6) to the centre

in order to lock the appliance in its disabled state.

Only lay down the appliance when it has stopped running

completely. Do not place it on a dusty surface as

particles of dust could get into the mechanism.

CHARGING THE BATTERY

Fig. F

The included battery is delivered in non-charged

condition.

• Only use the battery charger in a temperature range

between +5º to + 40º Celsius.

• Only use the battery charger in dry, ventilated

rooms.

CHARGING

• Place the battery holder on a flat table and put the

battery in the battery holder. Pay attention to + and -

pole markings.

• Put the adapter plug of the net adapter in the

connector on the side of the battery holder.

• Put the net adapter in the socket.

• The red charging lamp on the battery holder will

illuminate indicating the battery is being charged.

• The charging process of a fully discharged battery will

take approximately 5 hours the first time and

afterwards approximately 3 hours.

After the charging time the red light will not switch

off automatically! Remove the battery within 5

hours from the charger. If the battery is not removed from the

charger after the charging period it may become overheated.

DISCHARGING THE BATTERY

Not only charging batteries is important, dischar-

ging is of equal importance or even greater

importance.

• When the battery is charged the cordless drill has to

be used until you start noticing that the power of the

drill is diminishing and that the maximum rotational

speed is not reached.

• The battery is almost discharged now. Only now you

can start charging the battery.

• Charging the battery while it is still charged for say

one-third of capacity, the so-called ‘memory effect’

can occur. Since during charging only the discharged

part of the battery capacity of the battery is being

charged now, the battery can start crystallizing in the

one-third that is still charged. This part of the battery

capacity can never be used afterwards.

• Do not discharge the battery to the minimum. As

soon as you notice that the power or the maximum

rotational speed is diminishing, you have to charge

the battery. When you proceed using the drill and

the battery becomes fully discharged, the so-called

‘switch of poles effect’ can occur. The polarity of the

battery poles will be switched: the ‘+’will become ‘-‘

and the ‘-‘ will become the ‘+’. Once this has

occurred the polarity will remain switched during

loading and this will damage the battery irreparable.

When the cordless drill is not being used over a

longer period of time, the battery has to be charged

fully first. The battery has to be stored in charged condition.

5. MAINTENANCE

These appliances are designed to function without

difficulty for a long time and to require minimum

maintenance. You will prolong the appliance's life by

cleaning it regularly and using it correctly.

Cleaning

Clean the housing regularly with a soft cloth, preferably

every time it is used. Keep the air vents free of dust and

dirt. Remove stubborn dirt with a soft rag moistened in

soapy water. Do not use any solvents such as petrol,

alcohol, ammonia, etc. as such substances can damage

the plastic parts.

Lubrication

The appliance does not need any extra lubrication.

Faults

If a fault arises through wear in an element, please

contact the service address shown on the warranty card.

A drawing of the spare parts that may be obtained is

included at the end of these operating instructions.

ENVIRONMENT

To prevent damage during transport, the appliance is

delivered in a solid packaging which consists largely of

reusable material. Therefore please make use of options

for recycling the packaging.

Nickel-cadmium batteries can be recycled. Deliver them

to a disposal site for chemical waste so that they can be

recycled or disposed of in an environmentally friendly

manner.

Ferm 544 Ferm

Bedømmelse

Mere om denne brugsanvisning

Vi forstår, at det er rart at have en papirbrugsanvisning til din FERM CDM1005 Bore-skruemaskine. Du kan altid downloade brugsanvisningen fra vores hjemmeside og selv printe den. Hvis du gerne vil have en original brugsanvisning, anbefaler vi, at du kontakter FERM. De kan muligvis levere en original brugsanvisning. Leder du efter brugsanvisningen til din FERM CDM1005 Bore-skruemaskine på et andet sprog? Vælg dit foretrukne sprog på vores hjemmeside, og søg efter modelnummeret for at se, om vi har det tilgængeligt.

Specifikationer

Alle brugsanvisninger til FERM Bore-skruemaskiner
Flere brugsanvisninger til Bore-skruemaskiner

Ofte stillede spørgsmål om FERM CDM1005 Bore-skruemaskine

Vores support-team søger efter nyttige produktoplysninger og svar på ofte stillede spørgsmål. Hvis du finder urigtigheder i vores ofte stillede spørgsmål, må du meget gerne lade os det vide ved at bruge vores kontaktformular.

Relaterede produkter

Brugsanvisning

FERM CDM1119 Bore-skruemaskine

Brugsanvisning

FERM CDM1014 Bore-skruemaskine

Brugsanvisning

FERM CDM1038 Bore-skruemaskine

Brugsanvisning

FERM CDM1037 Bore-skruemaskine

Brugsanvisning

FERM CDM1008 Bore-skruemaskine

Brugsanvisning

FERM CDM1003 Bore-skruemaskine

Brugsanvisning

FERM CDM1132 Bore-skruemaskine

Brugsanvisning

FERM CDM1036 Bore-skruemaskine

Relaterede kategorier