Brugsanvisning Beurer HD 82 Stockholm Elektrisk varmetæppe

Brugsanvisning

12

6. OPERATION

6.1 Safety

NOTICE

•

The device is fitted with a SAFETY SYSTEM. This sensor

technology provides protection against overheating across the

entire surface of the heating element with an automatic switch-

o in the event of afault. If the SAFETY SYSTEM has switched

o the device, the control will no longer light up in any way,

even when switched on.

•

Please note that for safety reasons, the device can no longer be

operated after a fault has occurred and must either be disposed

of or be sent to the specified service address.

•

Do not under any circumstances connect the defective heating

element with another control of the same type. This would

also trigger apermanent switch-o by the safety system in the

control.

6.2 Initial use

NOTICE

Ensure that the heating element will not bunch up or become

folded during use.

1.

First, connect the control

2

to the

heating element by inserting the plug-

in coupling

6

.

2.

Then plug the mains plug

1

into the

socket.

6.3 Switching on

Set the ON/OFF slider

3

to the ON ( I )

position to switch on the device (see

figure of control). The temperature settings

5

will then light up.

6.4 Setting the temperature

To increase the temperature, press the button

4

. To decrease

the temperature, press the

button

4

.

Level 0: OFF

Level 1: minimum heat

Setting 2 - 5: individual heat setting

Level 6: maximum heat

The fastest way to warm up the device is to initially set the

highest temperature setting.

6.5 Automatic switch-o

This device is equipped with an automatic switch-o function. This

turns o the heat supply approx. 3 hours after the initial use of

the device. This is indicated by a flashing temperature setting. In

order to reactivate the device, the sliding switch

3

must initially

be set to o (“0” position). After about 5 seconds it is possible to

switch it on again.

 WARNING

If the device is being used over several hours, we recommend that

you set the lowest temperature setting on the control to avoid the

body overheating and thereby any potential burns to the skin or

heat stroke.

6.6 Switching o

Set the ON/OFF slider to the OFF (0) position to switch o the

device. The temperature settings are then no longer illuminated.

If the device is not being used for several days, set the

slider to the OFF ( 0 ) position and remove the mains plug

from the socket.

Then disconnect the control

2

from the heating element

by unplugging the plug-in coupling

6

.

7. CLEANING AND MAINTENANCE

 WARNING

Before cleaning, always remove the power plug from the socket

first. Then disconnect the control from the heating element by

unplugging the plug-in coupling. Otherwise there is a risk of

electric shock.

NOTICE

The control must never come into contact with water or other

liquids, as this may cause damage.

•

To clean the control, use adry, lint-free cloth. Do not use any

chemical or abrasive cleaning agents.

•

Small marks on the heating element can be removed with

adamp cloth and, if necessary, with alittle liquid detergent for

delicate laundry.

NOTICE

Please note that the heating element must not be chemically

cleaned, wrung out, tumble dried, put through amangle or ironed.

Otherwise the heating element may get damaged.

•

The heating element is machine-washable.

•

Set the washing machine to aparticularly gentle wash cycle

at 30°C (wool cycle). Use a delicate laundry detergent and

measure it out according to the manufacturer’sinstructions.

•

Immediately after washing, reshape the heating element to its

original dimensions while it is still damp and spread it out flat

on aclothes horse to dry.

NOTICE

•

Do not use pegs or similar items to attach the heating element

to the clothes horse. Otherwise the heating element may get

damaged.

•

Do not reconnect the control to the heating element until the

plug-in coupling and heating element are completely dry.

Otherwise the device may get damaged.

 WARNING

Never switch the device on to dry it! Otherwise there is arisk of

electric shock.

8. WHAT IF THERE ARE PROBLEMS?

Problem

The temperature settings are not illuminated

despite the fact that

- the control is properly connected to

the heating element

- the power plug is connected to awork

-

ing socket

- the ON/OFF slider on the side of the

control is switched on ( I ).

Possible cause The safety system has switched the device

o permanently.

Solution Send the heating element and the control for

servicing.

Bedømmelse

Mere om denne brugsanvisning

Vi forstår, at det er rart at have en papirbrugsanvisning til din Beurer HD 82 Stockholm Elektrisk varmetæppe. Du kan altid downloade brugsanvisningen fra vores hjemmeside og selv printe den. Hvis du gerne vil have en original brugsanvisning, anbefaler vi, at du kontakter Beurer. De kan muligvis levere en original brugsanvisning. Leder du efter brugsanvisningen til din Beurer HD 82 Stockholm Elektrisk varmetæppe på et andet sprog? Vælg dit foretrukne sprog på vores hjemmeside, og søg efter modelnummeret for at se, om vi har det tilgængeligt.

Specifikationer

Alle brugsanvisninger til Beurer Elektriske varmetæpper
Flere brugsanvisninger til Elektriske varmetæpper

Ofte stillede spørgsmål om Beurer HD 82 Stockholm Elektrisk varmetæppe

Vores support-team søger efter nyttige produktoplysninger og svar på ofte stillede spørgsmål. Hvis du finder urigtigheder i vores ofte stillede spørgsmål, må du meget gerne lade os det vide ved at bruge vores kontaktformular.

Relaterede produkter

Brugsanvisning

Beurer HD 82 Helsinki Elektrisk varmetæppe

Brugsanvisning

Beurer UB 101 Elektrisk varmetæppe

Brugsanvisning

Beurer UB 91 Elektrisk varmetæppe

Brugsanvisning

Beurer TS 19 Elektrisk varmetæppe

Brugsanvisning

Beurer UB 74 Elektrisk varmetæppe

Brugsanvisning

Beurer TS 26 XXL Elektrisk varmetæppe

Brugsanvisning

Beurer HD 150 XXL Nordic Elektrisk varmetæppe

Brugsanvisning

Beurer HD 75 Cosy Elektrisk varmetæppe

Relaterede kategorier